Homepage About Us Online Store News Career Contact Us

Please contact us for stock availability, sales prices and fixed repair prices.

Contact UK

Adobe Acrobat Reader is required to
veiw PDF files.

Click Logo Below to download
Adobe Acrobat

Please note that PDF's may take a while to download

Back To Legacy Disk and Tape Emulators

AEM-6C

Form, Fit, Function Upgrade for the
HP1000 M/E/F-Series, 79xx Series Disk Drives.

Featuring:

  • Multi-Access Controller Interface.
  • 13037 MAC Disk Controller Plug-Compatible.
  • No Changes to Hardware or Software.
  • Coexists with HP 79xx Series Drives.
  • FAST Solid State Disk - Fully-Cached with write-thru to SCSI Hard Drive or MO Disk.
  • 5 msec Seek Time.
  • Removable Media for Fixed Disk.
  • Multiple Volumes on a single disk - Thumbwheel Selectable.

Replaces HP 79xx Disk Drives:

7905A 15 MB
7906A-M 20 MB
7920A-S 50 MB
7925A-S 120 MB

PLUG-COMPATIBLE & COEXISTS with HP DRIVES

The AEM-6C is an upgraded data storage system to replace HP 79xx Disk Drives using the 13037 Multi-Access Controller (MAC) interface. Merely unplug the existing drive and install the AEM-6C using the same data and multi-unit cables.

The AEM-6C can be added to an existing system, along with the present drives. The AEM-6C supports simultaneous operation with the existing drives, or with other AEM-6Cs.

Fixed / Removable Disk Emulation

79xx Series drives with fixed platters and removable disk cartridges can be replaced, while adding features and capabilities not available to the original drives. In fact, the AEM-6C can be setup to store data sent to the original fixed and removable platters in two different ways. The data can be stored on two SCSI drives, one for the fixed portion and a second for the removable cartridge data. Each drive (or cartridge) can be removed and stored as a backup, independently. This “Separate Image” setup mimics the original drive’s operation, but has the added benefit of larger capacity, reliability, and removability of the data.

AEM-6C configured with dual Magneto Optical SCSI disks for fixed and removable storage.

In cases where the fixed and removable data can be stored as a set, the images can be combined on a single SCSI device - hard drive or MO for example. The “Combined Image” mode offers the benefit of keeping the removable data and fixed-platter data together on one disk, allowing simple copies and backups of all data with less chance for error. With fixed and removable data stored on one disk, TPSs or classified data are easily removed for storage.

AEM-6C shown above the original 7906 drive, which it replaces.

AEM-6C emulator for the HP 1000 with MAC (Multi-Access Controller)interface includes removable SCSI hard drive (top-right) and disk to disk copy/backup to the secondary SCSI hard disk (lower-right).

MORE DATA STORAGE - FEWER DISKS

MultiVolume provides additional data storage by creating multiple volumes on the SCSI drive. One to 80 volumes can be stored on the disk, limited by disk capacity. The panel-mounted thumbwheel switch allows operator selection of the active volume. Changing the thumbwheel switch during operation has the effect of spinning the drive down, removing the disk, exchanging it with another, and spinning the drive up. MO disks are available in 128 MB to 540 MB capacity - Jaz disks are 2 GB, with standard SCSI hard disks providing additional capacity for more volumes and larger disk drives.

SOLID STATE DISK - FULL-DISK CACHING

The AEM-6C includes Full-Disk Caching. The entire drive image is held in cache memory. Changes in the cache memory are continuously transferred to the SCSI storage device, which can be a hard disk or Magneto Optical. Full-Disk Caching also provides a faster performing emulation. Seek times, head switching and blocking times are eliminated. Data is available instantly, providing 30% to 50% faster operation than the original drive.


Rear panel of the AEM-6C showing the PC Board Edge “Control” connector and “Data” connector. Connectors are plug-compatible with the original cables.

LOW MAINTENANCE - RELIABLE OPERATION

The AEM-6C uses SCSI disk drives for low maintenance operation. Drives are rated in excess of 300,000 hours MTBF and up to five years of continuous operation. Drives appear defect-free to the host computer.

REDUCED POWER, COOLING, and WEIGHT

The AEM-6C uses significantly less power and requires less cooling than the original. A modern switching power supply replaces the original, heavy analog supply. Power consumption is reduced from over 400 Watts to 29 Watts; weight of the drive is reduced to 29 lbs!

SPECIFICATIONS

INTERFACE
Multi-Access Controller (MAC) compatible with 13037A-D Disk Controller interface. Single port access. Compatible with additional OEM drives and/or AEM-6C units.

Control - 50-contact male card-edge connector, mates with
OEM cable. (MAC Interface)

Data - 3-pin keyed connector mates with standard OEM Multi-Unit cable. (MAC Interface)

Control/Maintenance - RS-232 serial port, ASCII (8, N, 1),
RJ-11 modular and DB-9 connectors.

DATA TRANSFER RATE
100% of existing drive transfer rate.

CACHE BUFFER
Size 32 to 256 MBytes
Capacity Full drive capacity

SEEK TIMES, TYPICAL
Track To Track, max 5 ms
Access, max 5 ms

RELIABILITY
MTBF 200,000+ hours
MTTR 15 minutes

POWER
Input Voltage 90 - 135, 180 - 264 VAC (Selectable)
Frequency 47 - 63 Hz
Power 50 - 90 Watts (Maximum)

PHYSICAL

High x Wide x Deep; Weight
Rack Mount/ 5.25 in. x 19 in. x 17.5 in.; 23 / 33 lbs
Table Top 133 mm x 483 mm x 445 mm; 10.5 kg

Drive Module 1.7 in. x 4.6 in. x 8.2 in.; 3 lbs
43.2 mm x 117 mm x 208 mm; 1.4 kg

Specifications subject to change without notice.

Replaces HP Disk Drives

• 7905A 15 MB
• 7906M 20 MB
• 7920A-S 50 MB
• 7925A-S 120 MB

 

Please contact us for stock availability, sales prices and fixed repair prices.
Back to top
Contact Uk

design by: gencon